Toronto · Mississauga · Brampton · GTA
TorrHandyman Logo
Plumbing & Fixtures

How to Replace a Kitchen Faucet: A Step-by-Step Guide

By Torr Handyman team

To replace a kitchen faucet, buy a faucet that fits your sink's hole layout, shut off and drain the supply lines, disconnect and remove the old faucet, mount the new one, connect the supply lines and flush the lines with the aerator removed before normal use. Most of the effort is under the sink, where old mounting nuts and shut-off valves are usually the hardest part.

About this guide: written by the Torr Handyman team, a Toronto handyman company with a licensed plumber on the team. The cover image and the images below are illustrations, not photos of our jobs. Questions about your own faucet? Contact us.

Key Takeaways

  • Count the holes in your sink (or countertop) before you buy. A one-hole faucet can cover a three-hole sink with a deck plate; a two-handle faucet can't fit a one-hole sink.
  • Test the shut-off valves before you start. If a valve won't close fully, stop: replacing the valve comes first.
  • Connect the supply lines exactly as your faucet's instructions say, including whether to use tape or sealant. Delta notes that bits of plumber's tape and other installation debris can get caught in aerators (Delta Faucet).
  • Flush the new faucet with the aerator off before using it. Delta's instructions call for two minutes on full hot and cold (Delta Faucet).

Before you buy: match the faucet to your sink

A deck plate (also called an escutcheon) is the flat cover that sits under a faucet and hides unused holes in the sink. A shut-off valve (or angle stop) is the small valve under the sink that controls water to one supply line.

The new faucet has to fit the holes already in your sink or countertop. Look underneath and count them, including any hole used by a side sprayer, soap dispenser or air gap.

  • One hole: fits a single-handle faucet, including most pull-down models.
  • Three holes: fits a single-handle faucet with a deck plate covering the extra holes, or a two-handle faucet whose handles match the hole spacing.
  • Four holes: usually a faucet plus a side sprayer or soap dispenser.

Swapping like for like is the simplest route, because it avoids drilling or covering holes. Many single-handle faucets include a deck plate in the box; check the specifications before you buy. If you have a stone or quartz countertop and need a new hole, that is a job for a countertop fabricator, not a DIY drill.

Also check the faucet's spout reach and height against any window sill or upper cabinet, and make sure a pull-down hose has room to move under the sink without catching on the drain or garbage disposal. If the sink drains slowly, deal with that first; see drain cleaning.

Kitchen or bathroom: what changes

The steps below are written for a kitchen faucet, but a bathroom (lavatory) faucet follows the same order. The differences: bathroom faucets often come with their own pop-up drain assembly, which you install at the same time, and the space under a vanity is usually tighter. If you're replacing the vanity or more, see bathroom renovations.

If you're replacing a bathroom faucet, consider a WaterSense-labelled model. The U.S. EPA says WaterSense bathroom sink faucets use a maximum of 1.5 gallons per minute, which can reduce a sink's water flow by 30% or more from the standard 2.2 gallons per minute, and that labelled faucets are certified lead-free (EPA WaterSense). The EPA has no WaterSense criteria for kitchen faucets, so a kitchen faucet won't carry the label.

Tools and parts

  • Basin wrench: a long-handled wrench with a pivoting jaw that reaches mounting nuts behind the sink bowl
  • Two adjustable wrenches
  • Bucket and old towels
  • Flashlight or headlamp
  • New braided stainless supply lines, if your faucet doesn't include them
  • The gasket or deck-plate seal supplied with the faucet (some instructions call for plumber's putty or silicone instead; follow yours)
  • Penetrating oil, for corroded nuts

Read your new faucet's installation sheet before you start. Manufacturer instructions vary by model and take priority over any general guide, including this one.

Illustration of a faucet supply line being connected under a kitchen sink
Illustration only, not a photo of a Torr Handyman job.

Step 1: Shut off the water and test the valves

Close the hot and cold shut-off valves under the sink by turning them clockwise (a quarter-turn valve only needs a 90-degree turn), then open the faucet to relieve pressure and drain the remaining water. If water keeps running after the valves are closed, a valve isn't sealing. Don't continue: close the main water shut-off and replace the valve first, or call a plumber.

In a condo, the unit's shut-offs may be in the kitchen cabinet, behind an access panel or in a utility closet. If you can't find them, ask your property manager before you start, because shutting water off at the riser affects other units.

Step 2: Disconnect the supply lines

Put the bucket under the connections. Hold each shut-off valve steady with one wrench and loosen the supply line nut with the other, so you don't twist the valve or the pipe behind it. Disconnect the pull-down hose from its quick-connect fitting if your old faucet has one, and remove the hose weight.

Step 3: Remove the old faucet

Use the basin wrench to loosen the mounting nut (or nuts) holding the faucet to the underside of the sink. Older faucets often have corroded nuts: spray them with penetrating oil, wait several minutes and try again. If the old faucet has a separate side sprayer or soap dispenser, remove its nut from below too. Lift the old faucet and deck plate out from above.

Scrape away old putty or sealant, then clean the sink surface so the new gasket sits flat. Any grit left under the gasket can let water seep underneath. While the faucet is out, check the bead around the sink edge too; cracked or mouldy sealant is a separate fix (sink caulking).

Step 4: Mount the new faucet

Set the gasket or deck plate in place, then feed the faucet's supply lines and mounting shank through the holes from above. Centre the faucet, then tighten the mounting hardware from below following your instructions. Many faucets use a shank nut that you tighten by hand and finish with the supplied tool; over-tightening can crack the deck plate or distort the gasket.

Step 5: Connect the supply lines

Connect the hot line to the hot valve (on the left as you face the sink) and the cold line to the cold valve. Thread each nut by hand first to avoid cross-threading, then snug it with a wrench while holding the valve with a second wrench.

Connection types vary by brand and model, so follow your faucet's instructions on whether to use tape or sealant on each connection. Delta notes that particles of plumber's tape, solder and copper left from installation can get caught in aerators (Delta Faucet), so loose tape fragments are worth avoiding.

For a pull-down faucet, click the hose into its quick-connect and clip the hose weight on at the position the instructions show. If the weight is too high or too low, the spray head won't retract fully.

Step 6: Flush the lines and check for leaks

Unscrew the aerator from the tip of the spout. Delta's instructions say to remove the aerator and its sealing gasket, turn the handles to full hot and cold, flush the lines for two minutes, then reinstall the aerator (Delta Faucet). Flushing clears debris loosened during the work, which can otherwise collect in the aerator.

Then dry every connection under the sink with a paper towel, run the faucet hot and cold for a few minutes and check again for drips. Check once more the next day: a slow drip on the cabinet floor may only show up after several hours.

Illustration of a newly installed pull-down kitchen faucet with water running
Illustration only, not a photo of a Torr Handyman job.

When to stop and call a professional

Replacing a faucet is a reasonable DIY job when the valves work and the nuts come loose. Stop and get help if:

  • A shut-off valve won't close fully, leaks at the stem or crumbles when you touch it.
  • The mounting nuts are seized and you risk cracking the sink.
  • The supply pipes behind the valves move or leak when you turn the nuts.
  • You need a new hole drilled in stone or quartz.
  • You live in a condo and a leak could reach the unit below.
  • Valves close fully, nuts come loose, same hole layout: DIY with the steps above
  • Faucet drips but the body is in good shape: Repair the cartridge or washer instead of replacing the faucet
  • Seized valves, corroded pipes or a condo unit above someone: Hire a plumber or experienced handyman

For reference, Torr Handyman's published Toronto prices are faucet installation from $280 plus tax and kitchen faucet repair from $180 plus tax (faucet repair and installation prices).

Frequently asked questions

Can I replace a kitchen faucet myself?+

Yes, if your shut-off valves close fully and you can reach the mounting nuts. The job needs basic tools plus a basin wrench. Stop and call a pro if a valve won't close, the nuts are seized or the pipes behind the valves are damaged.

Do I need plumber's tape on faucet supply lines?+

It depends on the connection. Follow your faucet's instructions, since connection types vary by brand and model, and only add tape or sealant where they call for it. Loose tape fragments can end up in the aerator.

Can I put a single-handle faucet on a three-hole sink?+

Yes. Use a deck plate (escutcheon) to cover the two unused holes. Many single-handle kitchen faucets include one; check the specifications before you buy.

Why is my new faucet sputtering or low on pressure?+

Debris from the old pipes often lodges in the aerator after a faucet swap. Remove the aerator, rinse the screen, and flush the lines as described in Step 6.

Sources



← Back to Blog